0

Your Cart is Empty

2012-2017 FX HO / FX SHO/ FX Cruiser HO / FX Cruiser SHO /SVHO Yamaha

130BT423

All mat kits come standard with BlackTip Jetsports's exclusive PSA (pressure sensitive adhesive) to make installation easy - without the big mess of having to glue them down. Simply peel the backing off - press the mats into place and they are ready to go. This is an easy afternoon job and makes a world of difference on how your ski looks.

Color samples may be sent to you upon request or viewed by clicking this link Color Samples BlackTip Jetsports Traction Mats are in stock and usually available same day in Cut Groove Black. *Please note, we only accept returns on black cut-groove mats. All other mats are not stocked and considered custom. Each kit is specific to the Year, Make and Model of your craft, please verify this information before purchasing.



If you need assistance ordering or just have a few questions, please contact a member of our team by email Sales@WatercraftSuperstore.net or by toll free 866-957-9277. To complete your custom BlackTip Jetsports look, please visit our BlackTip Jetsports Custom Seat Covers **Red Traction Mats may fade if left uncovered while not in use.**

2012 FX HO
2012 FX SHO
2012 FX CRUISER HO
2012 FX CRUISER SHO

2013 FX HO
2013 FX SHO
2013 FX CRUISER HO
2013 FX CRUISER SHO

2014 FX HO
2014 FX SHO
2014 FX SVHO
2014 FX Cruiser HO
2014 FX Cruiser SHO
2014 FX Cruiser SVHO

2015 FX Cruiser SVHO
2015 FX SVHO
2015 FX Cruiser SHO
2015 FX SHO
2015 FX Cruiser HO
2015 FX HO

2016 FX SVHO
2016 FX Crusier SVHO
2016 FX Cruiser SHO
2016 FX Cruiser HO
2016 FX HO

2017 FX HO
2017 FX Cruiser HO
2017 FX SVHO
2017 FX Cruiser SVHO
2017 FX Limited SVHO
Removal of original riveted mats :Drill the heads off of the rivets holding down the original mats while pushing the remaining rivet into the hull. Fill the holes left by the rivet with 5min. epoxy, this can be purchased locally at any auto parts store. Make sure to scrape the epoxy flat in the foot wells so the new mats will lay flush. Clean the area that the new mats will be attached to with acetone solvent for proper adhesion.

Removal of original glue down mats:By hand, peel off any old mat material that you are able to and then you use a putty knife to help remove all material from the difficult areas. Areas that are difficult may require spraying WD-40 brand lubricant in between the mat and hull to help loosen the old adhesive. Take your time on the prep work; this is important to achieve professional results.

Now that your surface is clean and ready for the new mats it is time to lay out how your mats will look in the foot wells. This is the location the mats will be attached. Trace around the mats using a pencil. This is your reference area to place the mats after the paper is peeled off the back of the mat.

Peel off the paper backing from the mat and line up one end of the mat to your traced out area. (Do Not Try to Install the complete mat in one shot) Slowly work the mat down into your outline.

After the entire mat is installed you must apply even pressure down on top of the mat to insure complete contact to the hull.

Let mats sit for 12 hrs after the install so the glue will fully cure.
Watercraft Superstore's BlackTip Jetsports traction mats have a 1 year manufacturer's warranty against defect in material and workmanship. This warranty does not cover fading, tearing or stains due to user negligence. We do our best to make sure every traction mat set is perfect, but sometimes things happen.

If you should have a problem, please contact Watercraft Superstore @866-957-9277 or sales@watercraftsuperstore.net to identify your issue.
Use only mild dishwashing soap to clean your mats, if you must clean grease from the mats we suggest using Simple Green brand cleaner only to do so.